Autronic Smc Wiring Diagram

Also suits sm3 marine) smc std loom (rev c loom: This wire is responsible for turning the msd on and off.

Installation Of Autronic SMC

Attached is my proposed ign wiring diagram and.

Autronic smc wiring diagram. I keep this page online for those who like to see this wiring with the old ignitor, and stock coil. Sm2 firmware revisions v1.34 to v2.06. This is not the latest model but it remains supported by autronic.

Shielded wires from distributor to reluctor interface Select manufacturer "autronic" model "sm4". They are an excellent choice as replacements for most oem modules.

Autronic automotive controls official website. Autronic systems have been successfully installed on many vehicles such as rally cars, off road vehicles, street cars, powerboats, offshore powerboats, and in other forms of racing. Autronic smc is sequential 3d ecu available in three case styles, standard, sealed and water proof.

Computer required hardware the computer must have the following hardware •vga graphics adaptor (or compatible adaptors). The basic autronic smc kit includes harness, air temp sensor, internal map sensor, fuel pump relay, pc data cable, calibration and data logging software, and 100 page manual. Near engine ecu reluctor interface connected between distributor, and autronic smc.

The internal map sensor is available in 4.4 bar absolute (50 psi). Refer to race studio configuration user manual for further information concerning the loggers configuration. This page contains the wiring diagrams for my european spec st185.

Available in single, twin, triple and quad channel versions. This ecu is currently loaded with the map for the 964. The calibration and data logging software supplied with autronic smc ecu may be used with computers operating under windows 95/98/me/xp or 2000.

Autronic smc manual ver 1.6 5 introduction congratulations on your decision to install an autronic engine management system to your vehicle. Autronic sm2 manual ver 1.6 5. I am going to retain the twin distributor setup with the use of 2 im112 ign modules and standard coilpacks but i have a few questions.

This is the biggest selling model and is suitable for most applications. The autronic smc includes harness, air and water temp sensor, internal map sensor, fuel pump relay, pc data cable, calibration and data logging software, 100 page manual. Connects to a switched 12 volt source such as the ignition key or switch.

Autronic smc manual ver 6. General purpose ignition modules suitable for use with all autronic ecus that are equipped with internal dwell control. The autronic smc sequential engine management system is our compact 2nd generation engine management system for engine performance upgrades.

It is our least complex solution for applications requiring up to 8 channel sequential fuelling. Installation and wiring guide introduction congratulations on your decision to install an autronic engine management system to your vehicle. This is the biggest selling model and is suitable for most applications.

The calibration and data logging software supplied with autronic smc ecu may be used. I hope this page helps to pool as much info on using an autronic smc on a 4g63. Autronic systems have been successfully installed on many vehicles such as rally cars, off road vehicles, street cars, powerboats, offshore powerboats, and in other forms of racing.

Suits all smc ecus) smc early loom (early loom: Simple triggering, a low pin count connector and minimum wiring complexity make for rapid low cost. This page describes, with diagrams, how i connected each part of my engine management system together.

Hello, i am currently in the process of making up a wiring loom for my 1uzfe (non vvti) running on an smc 1.92 lc ecu. (max current draw of.250 ma.) this wire connects to the coil positive (+) terminal. Supplied in kit from 1996.

Sm3 std wiring (using sm4 std loom. Autronic smc is sequential 3d ecu. Product development guided by scientific investigation, implemented using modern computer programming techniques in conjunction with sound electronic & mechanical engineering practice

Throughout the process of wiring my car for the autronic engine management, i kept track of exactly how i wired each component together.

Wiring Loom Page